These sump filters use a polyethylene high surface area media (K1 micro, K1, Hel-X, etc.) in a fluidized moving bed set-up. This motion is well illustrated by this sump:
Note the very important circular movement of the K1 media in the sump. It is important to note the following.
Many millions of dollars of research in the area of aquaculture have established that fluidized K1 beds are the best type of filter by a factor of 50% to 1800% on a cubic inch per cubic inch basis.
If one looks at the top line below one will see that fluidized K1 is 540/340 or 59% better than stationary 30 ppi foam and 540/30 or 1800% better than ceramic balls.
|Biomedia||Effective” surface area ft²/ft³||Effective” surface area m²/m³||Cubic inches to get 5ft²||Cubic inches to get 100ft²|
|Fluidized K1 media (60% loading in sump)||540||16||320|
|30 PPI foam in canister or sump||340||25||500|
|30 PPI foam powerhead operated sponge||340||25||500|
|30 PPI foam air operated sponge||300||29||580|
|Plastic pot scrubbers||280||31||620|
|Static K1 media||260||33||660|
|20 PPI foam in canister or sump||260||33||660|
|20 PPI foam powerhead operated sponge||260||33||660|
|20 PPI foam air operated sponge||230||38||751|
|Powerhead operated undergravel filter||140||62||1240|
|Aquarium gravel in canister or sump||140||62||1240|
|Air operated undergravel filter||120||72||1440|
|Blue Matala pads||120||72||1440|
|1/8 inch garden pumice or perlite||100||86||1720|
|1/2 inch lava rock||60||144||2880|
|Expanded clay pebbles||30||288||5760|
|Cubic inches to get 5ft² = (5/E.A.)x1,728 100ft²=(100/E.A.x1,728)|
Design of a Fluidized Sump
The best design for a fluidized bed sump is:
This design is the best design for an aquarium filter you can have. As a K1 fluidized bed, research has shown it is simply the most efficient filter there is. The design maximizes both the volume of water in the sump and the media volume in the sump. It is easily and rapidly serviced. It maximizes the protection against the pump running dry because of evaporation. It is a very simple design.
Replacing the Air Stones with Wavemakers
One little discussed area in filtration is the noise level. Fluidized beds need a whole lot of aeration and bubble to be effective. This amount of bubbles can be noisy, VERY noisy. And large air pumps can be noisy in their own right. If noise is a concern use wavemakers to do the fluidized bed movement.
Six 2.5 watt wavemakers will cost about $40 (less than a large air pump and several high quality air stones). Three wavemakers aimed across the bottom side of a sump and three aimed at the surface from just below the surface on the opposite side of the sump compartment are ideal. This arrangement will give excellent circular flow, great aeration, and a low noise level.
With the wavemaker fluidized bed it is very important to create large amounts of “choppy waves” on the water surface of the sump. These “choppy waves” aerate as well as air stones. An oxygen saturation of at least 80% will give beneficial bacteria the best environment for doing their work.
Light diffusers (white “egg crate” plastic) are a common element in many sumps. But the light diffuser plastic has become very thin and weak as of late. So for fluidized sump builds one should use acrylic panels with many holes drilled into it. It is much stronger than the light diffusers and the K1 can’t get through it if the drilled holes are smaller than the K1 diameter.
It is important to use at least two big socks for the pre-filter if you use socks. Socks can plug up quickly when used with a heavily stocked aquarium. Polyester mats are much preferred over socks as they do not plug up as fast and do not require the constant maintenance of socks. I use NO mechanical filtration in my K1 fluidized bed sumps.
Note that a fluidized bed will work well if the sock compartment and socks are removed and there are only two compartments. Because of the agitation of the fluidized bed large food and feces particles are broken up and digested rapidly by the K1 media, so there is little need for the socks. All my sumps have only two compartments and no mechanical filtration as I have all heavily stocked tanks.
The trade off for having no mechanical filtration is that one needs about 20% to 30% more water changes to keep the nitrate at one’s chosen level. This is because 70% to 80% of the protein nitrogen that enters the aquarium as food ends up as ammonia being excreted through the gills of the fish. Only 20% to 30% of the nitrogen ends up in feces and uneaten food which mechanical filtration can remove.
The Mechanics of Fluidized Beds in Aquarium Sumps
A fluidized bed filter is simply a container filled with water which has about 60% of the volume of the water filled with what is called “K1” filter media. This K1 filter media is from Kaldnes in Europe originally, thus the name. But many copies and cheap Chinese knock offs can be found on the internet.
Movement of the fluidized bed media is typically accomplished by air bubbles. A schematic of a typical fluidized bed filter or more properly called a mixed bed bioreactors, a moving bed biofilm reactor or a MBBR, is:
There are several do-it-yourself versions of them on YouTube. Try Joey (the King of DIY aquariums). He’s got a great book about DIY aquariums that is only $25 for the electronic pdf version. It has a fluidized bed design in it.
If one doesn’t want to do a do-it-yourself sump for a fluidized bed one is pretty limited. There are some very expensive but very good “reactors” put out by Bashsea which do a good job.
Joey has some “DIY bottle filters”, both with fluidized beds and with regular media. Avoid this DIY bottle design in all its variations. The flow through the bottle is too low to be an effective filter. An air operated filter needs a lift tube to move water through the filter.
Avoid the small in tank Ziss Bubble Bio Moving Bed Filter, like the DIY bottle filters this filter has no flow through it so it has little effect in the aquarium.
One can also buy any one of several commercial static sumps designs and convert them to fluidized bed sumps quite easily.
Virtually all fluidized bed designs use bubble aeration to move the media. It is important to stage the air stones in such a way as to get the media moving in a circular fashion, up with the bubbles, across the top of the filter, down the opposite side of the filter, and across the bottom.
The aeration provides the oxygen required for the beneficial bacteria to work at their best potential and the design has no dead spots where the biofiltration slows because of lack of oxygen.
How the Aquarium Fluidized Bed Works
The key to this filter is the inside of the K1 media. Inside the media a thin filmy brown “gunk” builds with time. This brown “gunk” is several different types of beneficial bacteria in a biofloc.
Because of the rapid movement of the media the brown “gunk” get the ideal fast flow rate required for optimum biofiltration. Also, the movement knocks out any excess brown “gunk” and prevents clogging of the media. I.e. this design is “self-cleaning”.
The best media for a fluidized bed for a home aquarist is the K1 plastic media in all its many variations. This media needs to be purchased in bulk as it is ridiculously expensive in small quantities. This media is typically loaded as to fill 60% of the volume of the water in the filter bed.
There are several other product besides K1 style media marketed for fluidized beds. They all do not work well in a home fluidized bed filter. Stick with only K1 media or similar designs made of white polyethylene plastic.
Poret®aqua Media is cubes of urethane foam marketed as a fluidized bed media. Poret®aqua Media is NOT a good media for fluidized beds. First off there is no flow through the media, which makes it very poor. Then there is the problem that the plastic which makes up the media, namely urethane, is heavier than water. So once the bubbles inside the foam dissipate (like in a few weeks) the foam media sinks and no longer circulates.
There is a type of media out of Germany called the “Mutag Biochip” which is a polyethylene foam disc. It will work about as well as K1 in a fluidized bed but it is somewhat difficult to keep in motion without it stacking up and stopping biofiltration. It can be made to work very well in commercial operation where there is constant engineering support. We do not feel that it is good for an aquarium fluidized bed. Note it cannot work in a static bed because of the tendency of the disks to stack with one another, like the chips in a box of Pringles.
Fluidized Bed Myths
Note that there are a lot of myths about fluidized bed filters. The chief one is that “old bacteria” get knocked off the media so robust “young bacteria” can grow. Bacteria reproduce by binary fission, one bacterium splits into two bacterium. So, there is no such thing as “old” bacteria.
What does happen is that the center of the K1 media becomes filled with a wispy soft biofloc which is brown in color. The flow of water through this biofloc is perfect for beneficial bacteria. As is the oxygenation provided by the air bubbles or the surface agitation. And the whole apparatus can’t sludge up and stop flow because of its design. When the biofloc moves out too far into the current in the K1 and starts to close down the holes, the excess biofloc gets knocked off and the holes don’t plug up. Thus the great filtration of a fluidized bed sump.
Another myth is that the fluidized bed K1 media needs to have several weeks of submersion before it can form a biofilm which weights it down and allow it to circulate in the sump. In truth there will be small bubbles in the K1 media when it is first put into the sump. These bubbles make the K1 float and refuse to circulate in the sump. The bubbles dissolve over a span of two to five weeks and the K1 will begin circulating.
Still another myth is that fluidized beds take much longer to cycle than standard media such as stationary ceramic media. Testing showed that the fluidized K1 cycled just about as fast as any other media.
Milliliters dilute Ammonia solution oxidized
|Filter||Average||15 days||30 days||45 days||60 days||75 days||90 days|
|1 inch of gravel||0,5||0.25||0,5||0.5||0,25||1||0,5|
|Bottem flow HOB||18||4||8||32||16||32||16|
|Fluidized bed sump||131||16||64||128||64||256||256|
Research on Fluidized Beds
As we stated above.
Many millions of dollars of research in the area of aquaculture have established that K1 fluidized beds are the best type of filter by a factor of 50% to 1800% on a cubic inch per cubic inch basis.
Now many will question this claim. So we have put together some very boring research on what the science says about this. If you are an OCD nerd like the author, read on:
In support of this claim here are four references on ammonia oxidation by the type of filter.
The difference between these reflects the difference in efficiencies for a fluidized bed over a static submerged bed filter. A fluidized bed filter is just two to three times more efficient than a submerged static media filter. This is because of the rapid speed with which the water circulates through the center of the fluidized bed media and the large effective surface area of the K1.
“Production in Intensive and Recycle Systems”, Muir et. al., 2000 is a useful reference. It compares the capabilities of the various filter media systems.
This corresponds very well with the first four references.
Still another similar reference is “Nitrification in Moving Bed and Fixed Bed Biofilters Treating Effluent Water from a Large Commercial Outdoor Rainbow Trout RAS”, Suhr, 2010:
“Expressed as volumetric total ammonia-N (TAN) removal rate, the MB filters had significantly higher removal rate (231 ± 17 g N−1 m−3 d−1) compared to the FB filters (92 ± 2 g N−1 m−3 d−1).”
Suhr set up four identical capacity filter sumps. Two with moving bed (MB) and two with fixed bed (FB) media. The moving beds had 2.5 times the filtration capacity of the fixed beds, confirming the data of the previous five references. This makes six references confirming the superior abilities of a fluidized bed filter.
This assessment of fluidized beds (to a fish farmer these are “Mixed Bed Bioreactors”, “Moving Bed Biofilm Reactors” or MBBRs) is confirmed by the very recent book “Recirculating Aquaculture Systems: A Guide to Farm Design and Operations”, Davison, 2018:
“The final filter to discuss is the mixed bed bioreactor (MBBR), the most widely adopted biofilter for large scale RAS operations. The MBBR has been adopted by most RAS designers and operators because of its efficiency, reliability, predictability and low cost.”
Most of the research on fluidized beds in aquaculture has been done in just the past twenty years so one needs to use relatively recent references.
Note that a fixed bed filter with 30 ppi foam in it will be about 63% as good as a fluidized K1 bed. The K1 is loaded 60% at 900 square feet per cubic feet while the foam is 100% loaded at 340 square feet per cubic feet. 60% of 900 is 540 square feet per cubic feet of filter. 340/540= 0.63.
The foam will typically need some periodic maintenance and partial cleaning while the fluidized K1 never needs maintenance. This is why MBBRs are so popular in aquaculture.
Note that there are some filtration systems which, if perfectly set up and heavily maintained, will surpass K1 fluidized beds. Sand filters, bead filters, and fluidized sand filters will all outperform K1 fluidized beds by a factor of two to three. But these systems are only suitable for public aquariums where there are several people in the maintenance department who spend all their time maintaining the expensive systems. These systems are not for home hobbyists.
Sumps in More Depth
For more information on other types of sumps click on these links:
8.6.2. Static Submerged Media Sumps
Note that many beginners are concerned about how to flow the water to a sump. The common refrain is “my aquarium isn’t drilled, how does the water get to the sump?” Click on this link to get some ideas: