A new version is available at aquarium-science.com.

7.6. Media oppervlakte

Foto van auteur

Auteur : David Bogert

Gepubliceerd :

Tijd om te lezen :
13 minuten
Difficulty : Level 6

Excerpt :

References on Ammonia and Surface Area If one is only concerned with ammonia oxidation, as little as five square feet of static submerged biomedia surface per pound of fish can be used to produce safe levels of ammonia and nitrite for tropical fish. A reference is useful here: Simply put, if you do a good ... Lees meer

References on Ammonia and Surface Area

If one is only concerned with ammonia oxidation, as little as five square feet of static submerged biomedia surface per pound of fish can be used to produce safe levels of ammonia and nitrite for tropical fish.

A reference is useful here:

Simply put, if you do a good job of removing the solids from the system with the mechanical filter, the amount of surface area present in the biofilter will determine how much bacteria you can grow, how much you can feed the fish, and, thus, how many pounds of fish the system can hold. A general rule of thumb is that it takes at least 5 square feet of biomedia to handle 1 pound of fish being fed at 2 percent of body weight per day.

“Constructing a Simple and Inexpensive Recirculating Aquaculture System (RAS) for Classroom Use”, David Cline, Southern Research Aquaculture Center, Auburn University, 2005.

This article recommends 5 ft2 of effective filter media surface per pound of fish. But this is for tilapia and catfish, which are very tolerant of bad water including moderate levels of ammonia and nitrite. And it is for a submerged static filter. The important point here is that it is the square feet of surface area available which is important in biofiltration.

Melanochromis maingano
Melanochromis maingano

If a pound of fish is fed at a 2% of body weight per day of dry fish food one needs to calculate the rough amount of ammonia per day this will produce to look at further references:

  • One pound is 454 grams.
  • A typical feed rate is 2% of weight
  • 2% of 454 grams (one pound) is 9 grams
  • Fish food is typically 40% protein.
  • Protein is typically 17% nitrogen. 9 x 0.4 x 0.17 = 0.612 grams nitrogen per pound of fish per day.
  • NH₄ to N ratio is 19/15 = 1.266
  • 1.266 x 0.612 = 0.775 grams ammonia per pound of fish per day.
Nimbochromis livingstoni
Nimbochromis livingstoni

The University of Arizona in one of their materials (https://ag.arizona.edu/azaqua/ista/ISTA7/RecircWorkshop/Workshop%20PP%20%20&%20Misc%20Papers%20Adobe%202006/7%20Biofiltration/Nitrification-Biofiltration/Biofiltration- Nitrification%20Design%20Overview.pdf) mentions the average ammonia removal rate on average of 0.5 gram ammonia per square meter per day. Since one square meter is roughly 11 square feet this is 0.775/0.5 = 1.55 pounds of fish per 11 square feet. 11/1.55 = 7 square feet per pound of fish per day for ONLY ammonia removal. This is quite close to the 5 square feet figure in the first reference.

Summerfelt, 2006 (“Design and Management of Conventional Fluidized-Sand Biofilters”) achieved an average removal of 0.3 grams ammonia per square meter. This is roughly 0.775/.3 = 2.58, 11/2.58 = 4 square feet per pound of fish per day for ONLY ammonia removal. Again, this is quite close to the 5 square feet figure in the first reference.

Leporinus fasciatus Banded Leporinus
Leporinus fasciatus – Banded Leporinus

The Food and Agriculture Organization of the United Nations in its booklet available on the website www.fao.org mentions the ammonia removal rate varying between 0.2 and 2 grams per square meter of specific surface. 0.775/0.2 = 3.875, 11/3.875 = 2.8 to 28 square feet per pound of fish per day for ONLY ammonia removal. If 2.8 to 28 is considered a binomial distribution the mean will be very close to the 5 square feet figure in the first reference.

All these materials are for aquaculture operations. So one might want a reference which talks about aquariums. Grommen (“An Improved Nitrifying Enrichment to Remove Ammonium and Nitrite from Freshwater Aquaria Systems”) shows in his study of aquariums an average removal of 0.47 grams of ammonia per square meter of media in aquariums. 0.775/0.47 = 1.65, 11/1.65 = 6.7 square feet per pound of fish per day for ONLY ammonia removal. This is quite close to the 5 square feet figure in the first reference.

Angelfish Pinoy Clown
Angelfish Pinoy Clown

This makes 6 references which come in at about very roughly the 5 feet per pound figure. So Ammonia oxidation is easy! We will use the following “rule”:

One Pound Of Fish Needs 5 Square Feet of Biomedia Surface Area for Ammonia Oxidation

This is with a caveat. This is ONLY a submerged bed figure. A fluidized bed might need only one square foot while a trickle filter might need ten square feet.

Another reference gives 1.7 square foot of biomedia surface in a fluidized bed required for ammonia oxidation for one pound of fish (“Design and Operation of Moving Bed Biofilm Reactor Plants for Very Low Effluent Nitrogen and Phosphorus Concentrations”, Rusten, 2007). The difference between 1.7 and 5 reflects the increased efficiency of a fluidized bed.

Pseudotropheus polit Lion's Cove
Pseudotropheus polit Lion's Cove

Kristal helder water

But giving crystal clear water is a different story than ammonia and nitrite. One pound of fish needs roughly 100 square foot of biomedia surface area to produce fairly clear water. This is a very important rule. It is paramount in fish keeping.

One Pound Of Fish Needs 100 Square Feet of Biomedia Surface Area for Healthy, Crystal Clear Water

This amount of biomedia give no nitrites, no ammonia, good water clarity and good fish health. It is twenty times the level required for good ammonia oxidation in a submerged media filter like a canister filter.

Nimbochromis venustus
Nimbochromis venustus

A Continuum

There is a very rough geometric progression when it comes to water parameters and surface area in a filter. This can easily be put in a table form for static submerged media:

Square feet of biomedia per pound of fishAmmonia and nitrite levelsWater clariityFish healthPlug Time for 30 ppi foam
40 – 0.5Very dullPoorOne week
20undetectableDullRedelijk2 months
100undetectable“Crystal clear”Goed2 years
500undetectableCrystal clearExcellentNooit

Note that the 4-20-100-500 progression here is called a geometric relationship (multiply the preceding number by five) and is quite common in natural systems.

  • All this is predicated on cleaning the biomedia only lightly when the flow noticeably slows down, cleaning the biomedia removes the beneficial bacteria which have slowly built up.
  • The biofilm and biofloc builds up slowly, so the capacity builds up slowly over very roughly six months
  • This is for a canister filter. A fluidized bed filter is two to five times more efficient while a sponge or trickle filter is half to one fourth as efficient.
OB Aulonocara
OB Aulonocara

Note this surface area rule is supported in the literature:

Remember: as an absolute minimum, your system needs at least: 2.5 ft2 of biological surface area/gallon of water (at low stocking densities and low feeding rates). For a healthier system, we would recommend: 10 ft2/gallon of water OR 100 square feet per pound of fish.

“Understanding Biological Surface Area in Aquaponics”, Michael, 2016:
Osteoglossum bicirrhosum Silver Arowana
Osteoglossum bicirrhosum – Silver Arowana

Other Variables

We need to emphasis that this analysis is extremely simplistic. There are a lot of variables that affect how well any biofiltration media performs. Some of those variables are:

1, Flow: There is a surprisingly small relationship with the flow rate. The faster the flow rate over the media the more it can help the fish. But this flow rate relationship is not as large as common mythology suggests. Doubling the flow rate only raises the filter rate by 9%. This number came from actual testing.

2, Opening size: the larger the opening in the media the longer the media can go without clogging up. Conversely, the larger the opening the lower the surface area. So this is a somewhat two edged sword that seems to be very roughly maximized at about one tenth to one eighth of an inch (2.5 to 3 millimeters).

3, Stocking: the heavier the stocking the faster the media will clog up. What is often missed is that beneficial nitrifying bacteria can be out competed for space by non-beneficial bacteria. The heavier the stocking the more this will occur. This will reduce the media efficiency even when unclogged.

Xenotilapia bathyphilus Congo Blue Princess Tanganyika
Xenotilapia bathyphilus – Congo Blue Princess

4, Amount of food: this is like the stocking variable. If a given stocking of fish is fed at a three percent of body weight per day level the media will be much less effective and clog up faster than if the feeding is at the one percent level.

5, Maturity: The longer filter media have been in place without cleaning the more “mature” the filter media and the better it will perform. This will be true until the flow slows down due to clogging.

6, Food protein levels: this interesting variable says that high protein food is much better for the filter than a low protein food. A 50% protein level food will give two and a half times the efficiency and the time to clog than will a 30% protein food. This desirability of high protein food has to do with biomass buildup rate and the carbon to nitrogen ratio of the food. Biomass will buildup much faster and have less exposed beneficial bacteria with a low protein food.

Amphilophus labiatus True Red Devil
Amphilophus labiatus – True Red Devil

7, Aeration: the better the aeration the better the media will perform. The aeration in an aquarium provides both oxygen and carbon dioxide to the beneficial bacteria. Good aeration aids both in the breakdown of ammonia and in the breakdown of dissolved organic compounds and lessens the clogging.

8, Free volume: the greater the free volume the more space is available for biofloc to form and do biofiltration

Vieja bifasciatus
Vieja bifasciatus

9, Temperature: pH, KH, GH en fosfaten in het water beïnvloeden het allemaal op zeer onvoorspelbare manieren

10, Ecology: And the “ecology” of the tank will vary, often in very surprising ways. The tiny single celled protozoan community is surprisingly important to the function of an aquarium filter and the composition of this community varies in the extreme from tank to tank.

11, pH: Biofiltration capacity is somewhat dependent on pH. If you have an acidic aquarium of pH of 6.5 triple the number. If your pH is 6.0 multiply the number by 10. Acid conditions need much larger surface areas than a 7.0 to 8.4 pH.

All these things are cumulative and can rarely make a 10 square feet per pound filter give crystal clear water. By the same token they can rarely make a 500 square feet per pound filter give cloudy water.

This somewhat unpredictable variation is why I put a downright ridiculous amounts of filtration on all my tanks. My big tanks all have large K1 fluidized bed sumps and multiple undergravel filters on them. Some of them have FX6 canisters on them. I almost NEVER clean a filter. And the water is crystal clear and the fish are very healthy despite being very heavily stocked.

Peacock Hybrid Ruby Red
Peacock Hybrid Ruby Red

Illustrations on How to Apply the Surface Area Numbers

Hier is een reactie op deze webpagina en het antwoord:

Paul

I have a 75-gallon community tank with an EHEIM 2217 canister filter. I’m planning to replace all the EHEIM filter media with Swiss Tropical 20 PPI Poret foam. I’m thinking of having 5 foam pads, each 2” thick and 7” in diameter. Would this give me the 220 sq. ft of effective surface area mentioned in your chart? Using one of your other charts, I calculate that I have 0.75 lbs of fish. Using the 100 sq. ft for 1 lb. of fish metric, I would think I’ll be able to easily accommodate more fish – is that right? I’m planning to use your recommendation to squeeze liquid from the existing filter pads onto the new pads to jump start the cycling of the new foam. How long do you think I should wait before adding more fish? Thanks for your help.

Dave

Oké, je hebt een cilinder van tien centimeter lang en zeven centimeter in diameter. V = πr2 h π x 3.5 x 3.5 x 10 = 384 This will give one 384 cubic inches of 20 ppi foam. 12x12x12 is 1,728 So you will have 384/1,728 or 0.222 cubic feet. 0.222 x 220 = 49 square feet. So you can do 0.49 pounds of fish at the 100 square foot per pound of fish metric. At the current time you are at (0.49×100)/0.75 = 65 square feet per pound of fish. 65 square feet is good, but it isn’t 100 square feet. So you cannot accommodate more fish.

En je kunt meteen vissen toevoegen en ze gewoon een paar weken niet voeren of letterlijk wachten zolang je je prettig voelt. Ik voeg vijvermodder toe (zie het artikel over het "volwassen aquarium") en wacht minimaal zes weken, maar ik ben een beetje gek.

Maskaheros argenteus
Maskaheros argenteus

Nog een voorbeeld van berekeningen van aquarium filtermedia

Deze uitwisseling komt uit het opmerkingengedeelte van deze website:

Vraag #1

Hi there,
I’m reaching out for some clarity on ‘Square Feet of Biomedia Surface Area’. I’m considering the 5″ Poret® Foam Sheets (26 × 19.5″ Sheet) and am wondering what the calculations would be for cubic sq. ft.? I plan on executing the ‘10 ft2/gallon of water’ OR ‘100 ft2/pound of fish.’

Antwoord #1

To calculate the volume the math is 5 inch x 26 inch x 19.5 inch / 12 inch x 12 inch x 12inch = 1.47 cubic feet per sheet of Poret® Foam. With a 20 ppi Poret® foam (what I recommend) which has about 220 square feet of effective surface area per cubic foot, this is 1.47 x 220 = 323 square feet. So If you use the whole sheet of Poret® you can support roughly 3.23 pounds of fish in a healthy environment (100 square feet of surface area per pound of fish). And I don’t recommend “10 ft2/gallon of water”. Go ONLY with the “100 ft2/pound of fish.

Vraag #2

Thank you so much for the reply but I’m still confused. Essentially I’m wondering how many – 5″ deep x 26″ long x 19.5″ high Poret® Foam Sheets, will I need for 13.2 lbs. of fish (24 × 8.8 oz Discus or 24 x 8.8/16)?

Antwoord #2

The calculation for 13.2 pounds of fish is 13.2 pounds divided by 3.23 pounds equals four sheets of 5″ deep x 26″ long x 19.5″ high Poret® Foam.

Deze voorbeelden illustreren het proces heel goed.

Labidochromis hongi redtop schweden hybrid
Labidochromis hongi – Redtop schweden hybrid

Sump Considerations

If one is doing the calculations for a sump one should be aware that fluidized bed K1 is roughly 58% more efficient than static 30 ppi foam as far as filtration. The effective surface area considerations are that fluidized K1 is 900 square feet per cubic foot of media. At 60% loading this becomes 540 square feet per cubic foot of sump filter.

Foam with 30 pores per inch has a surface area of 340 square feet per cubic foot. 540/340= 1.58

Champsochromis spilorhynchus
Champsochromis spilorhynchus

Nog een andere illustratie:

Vraag:

Hoe bereken je het oppervlak van media die word gebruikt voor biologische filtratie? Ik heb bijvoorbeeld 30 potwassers en wat schuim in een Fluval 407 potfilter op een tank van 75 gallon.

Answer:

OK Elke potscrubber is ongeveer negen kubieke inch medium (grote potscrubbers???). 9×30/12x12x12 = 0,156 kubieke voet. Potwassers zijn 260 vierkante voet per kubieke voet media (daar zou ik naast kunnen zitten). 0,156x 260 = 40 vierkante voet van de potwassers. Als ik het me goed herinner heeft een 407 een stuk schuim van 30 ppi dat 10 inch x 1 inch x 14 inch is. 10x1x12/12x12x12= 0,081 kubieke voet Schuim is ongeveer 340 vierkante voet per kubieke voet 0,081×340 = 27,5 vierkante voet. 27,5 + 40 = 67,5 vierkante voet. Dat is gewoon uit mijn hoofd. U moet de cijfers corrigeren, afhankelijk van de grootte van uw potscrubbers en de ware grootte van het 407-schuim.

A youtube video from HalfMan HalfCichlid about Surface Area:

The Biology of Filter Media- Why Surface Area is Critically Important